|
||||||||||
|
||||||||||
19 May 2010, 21:31 (Ref:2694367) | #1 | |
Racer
Join Date: Nov 2007
Posts: 108
|
Turbo engine under bonnet temperatures
Hi,
I have a Nissan Pulsar GTiR which is in a mild state of tune but it is running increased boost via an APEXi boost controller (figure unknown currently). It was previously used only for sprinting and other speed events and I have concerns that being used for circuit racing the temperatures are going to be much higher due to the duration of time the engine is going to be boosting. For those of you that don't know the Pulsar has a very aggressive bonnet vent which normally feeds the standard intercooler however as it has been converted and the intercooler is now front mounted this is now 'vacant' and is going to be instead delivering a large amount of cool air into the engine bay which is a bonus. Clearly I am going to have to fit an oil cooler but what sort of problems, if any, am I possible to face from the generated temperatures and can I do anything to improve safety/performance ie. wrap the manifolds, shield the wiring, fuel lines etc? Sorry for my novice questions but forced induction for competition is a new concept to me and I'd rather ask now than have an engine fire at my first event Thanks, Sam |
|
|
19 May 2010, 23:25 (Ref:2694427) | #2 | ||
Veteran
Join Date: Jun 2009
Posts: 4,125
|
We run a Porsche 944 Turbo, and the only issue we've experienced is a reluctance to start at the pitstops, which we put down to heat soak causing fuel vapourisation....we've wrapped the fuel lines in insulating foil, and after switching the engine off turn the ignition back on to keep the fuel pump circulating the fuel, and that seems to have cured the problem...(fingers crossed)
Don't know whether that helps! |
||
__________________
Richard Murtha: You don't stop racing because you are too old, you get old when you stop racing! But its looking increasingly likely that I've stopped.....have to go back to rallying ;) |
20 May 2010, 09:06 (Ref:2694577) | #3 | |||
Veteran
Join Date: Apr 2006
Posts: 1,935
|
Quote:
I use wrap, but it accelerates the aging of the manifold, inlets I use slivered insulation tape, not sure how much they actually do Every degree you drop inlet drops the same in exhaust, so check that High speed means you will likely see lower temps than the road |
|||
__________________
Contrary to popular opinion, I do have mechanical sympathy, I always feel sorry for the cars I drive. |
20 May 2010, 12:53 (Ref:2694712) | #4 | |||
Racer
Join Date: Aug 2007
Posts: 394
|
Quote:
Its important that the air that enters have a proper exit. We tend to open inlets and we forget about outlets... I dont recommend wrap for the exhaust in a high boost turbo unless many other considerations are taken in the design and its properly tested. Keeping a cool inlet is good like Notso said. And the oil radiator is a good thing if package adn weight are not a problem for you and you measure oil temp and choose a proper oil viscosity. |
|||
__________________
Racing is in my blood. |
20 May 2010, 15:37 (Ref:2694809) | #5 | |
Racer
Join Date: Nov 2007
Posts: 108
|
Thanks everyone, given me some food for thought. Particularly the stalled air theory. Will consider that when thinking about positioning the oil cooler.
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
TAG Turbo engine | porman | Racing Technology | 12 | 21 Jul 2010 16:06 |
TAG Turbo engine | porman | Motorsport History | 8 | 21 Mar 2010 23:03 |
TAG Turbo engine | porman | Sportscar & GT Racing | 6 | 19 Mar 2010 15:41 |
Bonnet raisers= lower engine temps?.. | Zico | Racing Technology | 8 | 9 May 2009 22:26 |
What C/R should be use on a 2L turbo engine? | TEAM78 | Racing Technology | 21 | 17 Nov 2005 12:57 |